Ara
Toplam kayıt 160, listelenen: 11-20
An experimental study on a bus air conditioner to determine its conformty to design and comfort condition
(Yildiz Technical University Press, 2017)
The air conditioning system for a bus should be selected considering a number of parameters, including passenger capacity, local climatic conditions, and fuel consumption. It is possible to determine whether a selected air ...
A micro-damage investigation on a low-alloy steel tested using a 7.62-mm AP projectile | [Raziskava mikropoškodb malolegiranega jekla po preizkusu s kroglo AP 7,62 mm]
(INST ZA KOVINSKE MATERIALE I IN TEHNOLOGIE, 2011)
Low-alloy steels have been widely used as an armor material in defense systems due to their superior mechanical and weldability properties. In this study, microdamage formation in an AISI 4140 steel, which was hit by 7.62-mm ...
Non-spatial analysis for the road traffic accidents
(ELSEVIER SCIENCE BV,, 2013)
Road traffic accidents are huge health and development problem. The number of the accidents has been increasing in Turkey as in the world. In this study the road traffic accidents in Osmaniye are analysed using chi-square ...
Flap kontrollü bir rüzgar türbini palasının aerodinamik parametrelerinin hesaplamalı akışkalar mekaniği kullanarak elde edilmesi
(IV. ULUSAL HAVACILIK VE UZAY KONFERANSI, 2012/9/12-)
Bu çalısmada, rijit olarak dönme hareketi yapan firar kenarı kanatçıklı NACA 633 418 kesiti bir hesaplamalı
akıskanlar dinamiği yazılımı kullanılarak (Ansys CFX)analizleri gerçeklestirilmistir. Bu amaçla öncelikle
Ansys ...
Momente maruz kazıkların nümerik olarak incelenmesi
(ÇUKUROVA ÜNİV., 2017)
Zemin mekaniği ve geoteknik mühendisliğinde kazıklı temellerin kullanımının önemi son yıllarda artmaktadır. Taşıma gücü zayıf zeminlerde, taşıma gücü ile ilgili yetersizliği ortadan kaldırmak için tercih edilen kazıklar ...
Effect of the martensite volume fraction on the machining of a dual-phase steel using a milling operation
(INST ZA KOVINSKE MATERIALE I IN TEHNOLOGIE, 2011)
Dual-phase steels are attractive because of their good combination of strength and ductility. However, an increase in the martensite content will decrease the steel's machinability significantly. Therefore, optimum cutting ...
The concept of owner representation and the problems stemming from the lack of ıts application
(2017)
Although construction owners have numerous technical responsibilities in the process of planning a construction project and completing it on time along to the plan, the owners in our country, Turkey, have not developed a ...
Valorization of wheat bran for the production of polygalacturonase in SSF of Aspergillus sojae
(ELSEVİER, 2013)
Wheat bran, among various agro industrial by products, screened for the production of polygalacturonase (PG) in solid-state fermentation of Aspergillus sojae mutant strain, was found to be the most suitable substrate without ...
Numerical investigation of flow and heat transfer in communicating converging and diverging channels
(Yildiz Technical University, 2018)
Fluid flow and heat transfer in communicating converging and diverging channel has been numerically investigated. Channels are assumed to be at constant wall temperature and the flow is assumed to be steady state and ...
Girintili bal peteği yapısının mekanik özelliklerinin geliştirilmesi
(3nd International Conference on Material Science and Technology in Cappadocia, 2018/9/17-)
Bu çalışmada, girintili bal peteği hücre yapısının
mekanik özellikleri analitik ve sayısal olarak
artırılmıştır. Normal girintili bal peteği yapısının
analitik ve sayısal analiz sonuçları karşılaştırılmış ve
birbirine ...